Felt bowls are cute, no doubt about it. Little fuzzy display bowls that can fit into one another, that’s even cuter! I decided to make some nesting bowls today, and documented the process to share with you.
If you know how to make felt already, and are looking for a craft that will provide you with two or three hours of crafting and will be suitable for an Easter display or gift, look no further. If you haven’t made felt at all yet, I would advise you to first try making a piece or two of flat felt, to get an idea of how felting works.
To start, I gathered my basic felting supplies. I used bubble wrap, soap, a kettle of water, loose wool (roving), scissors, and a measuring tape. You might also like to have a towel on hand, a bowl, and perhaps some paper and a pen.
I thought that I’d like to make three little nesting-bowls. I choose three colours of wool roving that coordinated well together. I decided to blend colours for two of the bowls, and wanted to add dashes of all the colours on all the bowls. I had intended to just make single-colour bowls, but I couldn’t help myself! Obviously, you can use whatever mix of colours you would like.
The basic procedure for making the bowls, no matter what size they are, is relatively simple. The challenge was to make bowls that would “fit into” one another… to account for sizing and so forth. I decided to make a simple bowl shape, then add 1 inch on every side for the next size up. I added about an inch or so to THAT one for the largest bowl. I cut all these templates out of bubble wrap. In retrospect, I’d have preferred to have made some smaller bowls, too. However, as I had saved my templates, I can make smaller ones at a later date.
To begin any sort of resist felting, lay out three layers of wool roving at right angles to each other, so that they extend about 2 inches past the template-size. In this case, I made sure that the top of the bowl didn’t have this extension, because it would be left open in the end. If I’d wanted to make a more spherical object, I could have extended the top end too. I like to lay my template under my piece of bubble wrap as a guide for the first overlapping layers. However if you find that is too hard to see through the bubble wrap you are working on, you can trace the template shape onto a piece of paper and place this under the bubble wrap to guide you. Remember it is important to extend up to about 2 inches PAST the template-shape, in order to create a meshing of wool.
Once the first three layers of roving have been placed, gently spray some lukewarm water onto them. Be gentle, allowing the water to just fall onto the wool. Next, place your template on top of this. Make sure that the top aligns with the top of the wool. Remember there should be almost 2 inches of extra wool all around the rest of the shape. Take this extra wool and fold onto the template.
The final step before really felting is to lay three more layers of wool roving, at right angles to one another, on top of this. Try to fill the entire “template” area, even though much of it is covered around the edges. This will ensure that there are no holes or awkward seam parts to your bowl.
Spray the wooly work again, being gentle. Then drizzle pure dish-soap overtop. Pour some boiling (or very hot) water on it, and then lay another piece of bubble wrap on top. Pat it (if it’s not too hot to do so!) and rub it. Pay special attention to rub the seam area… we really want the wool there to mesh quickly. After a minute or so of patting, flip the work over, and pat the other side.
Try opening the bubble-wrap up to rub the wool directly. Within a minute or so of patting and rubbing, you should be able to gently lift the object. Pry open the top part, and gently rub the edges. If it’s fused, force it open. It’s ok at this point; you can do almost anything to this malleable mass.
Lift the object, turn it in your hands. Rub the inside and outside of the seam area. If there are sparse patches or holes, try adding a little more wool roving on top. Put some more soap, a dash of water, and gently rub it in your hands. Work on the seam area, and rub the entire object.
Turn it inside out, and rub the inside on your bubble wrap. turn it back outside-out, and rub the whole object on the bubble wrap. Keep it open, don’t allow it to lay flat again.
After a few minutes, you can gently drop the object onto the table. Do this a few times, trying to hit a different part of the bowl each time. Start to hit it harder; and focus on any bumps or strange parts. It is almost magical, how the wool will tighten into felt as you do this. It will shrink quite a great deal, too! If you have a bathtub nearby, try hurling the wooly mass into it several times. Start more gentle, then hurl with all your might.
If the bowl is cold, pour some more boiling or hot water on it. Friction, compression, and heat all conspire to turn wool into felt. So, more heat can’t hurt!
Finally, when your bowl is looking like a bowl, set it. You can set it “rim-side-up” on a table, or you can stuff it with bubble wrap (like I’ve done in the examples) and turn upside down. Like a sweater that you lay flat to dry, wool felt will have a memory. It likes to maintain the shape that it is left to dry in.
If you are in the Montreal area and would like to take a felt-making class, please be in contact with me. I will be teaching this technique (and more!) in workshops of varying lengths. Happy felting!
Natasha Henderson, Montreal
- Sushi Rolled Felt Beads (fleurbain.com)